ATTENTION:
OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES
Removal/Installation of Major Assemblies -
eVo/eVo Wallette/Elite Edge Ion
Troubleshooting Information - Removal/Installation of Major Assemblies -
eVo/eVo Wallette/Elite Edge Ion
Megatouch Ion Technical Reference Manual
Touchscreen Removal
1. Turn off and unplug the game.
2. Unlock and open the CPU section and place something under the front bezel to brace it when
the strain relief cord is disconnected.
3. Remove the screw and washer fastening the strain relief cord, then remove the remaining 5
screws fastening the LCD mounting bracket to the game. The dongle socket ground wire will
also be removed in the process. See Figure 1.
4. Remove the nut, wire and bolt from the dongle socket assembly located on LCD mounting
bracket, then remove the bracket. See Figure 1.
5. Carefully cut the tie wraps around the VGA monitor cable, remove the ground wire and discon-
nect the cable from the monitor. See Figure 1.
6. Remove the OSD cable from the twist clamp and disconnect it from the OSD board and the
monitor. Then remove the OSD board from the Velcro attached to the hinge and set it aside.
See Figure 1.
7. Disconnect the LCD power connector (black and yellow wires). See Figure 2.
8. Carefully cut the tie wrap around the touchscreen controller cable and disconnect the cable
from the touchscreen controller. Also remove the ground wire. See Figure 1.
9. Disconnect the touchscreen power cable from the touchscreen controller (See Figure 1), then
disconnect the Molex connector identified by the orange and gray wires.
10. Loosen the 3 screws on the monitor side of the hinges in order to raise the hinges and allow
room to remove the monitor. See Figure 2.
NOTE: Elite Edge games may require you to remove the joystick in order to allow the
necessary room for loosening of the hinge screws. To remove the joystick, carefully place
the game on its side. Remove the 2 screws securing the protective bracket on the bottom
of the game and remove the bracket. Disconnect the joystick connector and remove the
joystick. Return the game to its upright position.
11. Slide the monitor out of the bezel.
12. Note the orientation of the touchscreen cable before removing the screen. Then use dental
floss to carefully cut the foam tape holding the touchscreen to the monitor until you are able to
completely remove the screen.
13. Remove any remaining adhesive residue with denatured alcohol, then clean the monitor glass
with the supplied alcohol wipe.
Troubleshooting Information - Removal/Installation of Major Assemblies -
eVo/eVo Wallette/Elite Edge Ion
Megatouch Ion Technical Reference Manual
ATTENTION:
OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES
Removal/Installation of Major Assemblies -
eVo/eVo Wallette/Elite Edge Ion (cont’d)
Touchscreen Installation
1. Clean the reverse side of the replacement touchscreen with the supplied alcohol wipe.
2. Cut pieces of the supplied 1/2” double-sided foam tape long enough to cover each edge of the
screen without overlapping. After the tape is in place on the screen, peel off the backing.
3. Replace the new touchscreen over the monitor in the same manner as the old screen, making
sure the screen is properly and evenly aligned over the monitor glass. Then clean the front of
the screen with the supplied alcohol wipe.
4. Carefully slide the new monitor into the bezel, making certain that the white edge of the moni-
tor and the monitor wire connections are facing the bottom of the bezel. Ensure that the
monitor is properly centered, then tighten the hinge screws. See Figure 2.
NOTE: If you removed the joystick on your Elite Edge, carefully return the game to its side and
reconnect the joystick to the connector in the game. Place the protective bracket in its previ-
ous position, sliding it under the lazy Susan and making sure the cutouts are placed around
the installed screws. Make sure all wires are secured inside the bracket, then reinstall the 2
screws securing the bracket. Return the game to its upright position.
5. Replace the LCD mounting bracket in the game and fasten it with the 6 screws removed
earlier. Also refasten the strain relief cord and the dongle socket ground wire. See Figure 1.
6. Replace the dongle socket assembly by securing the bolt, green wire and nut over the LCD
mounting plate. See Figure 1.
7. Connect the touchscreen controller cable to the touchscreen controller and secure it with a tie
wrap. Also restore the touchscreen controller cable ground wire. See Figure 1.
8. Connect the touchscreen power cable to the touchscreen controller (See Figure 1) and recon-
nect the Molex connector (orange and gray wires).
9. Connect the LCD power connector (black and yellow wires). See Figure 2.
10. Reattach the OSD board to the Velcro on the hinge, then connect the OSD cable to both the
OSD board and the monitor. See Figure 6. Secure the cable in the twist clamp.
11. Connect the VGA cable to the monitor and secure it with tie wraps. Also replace the ground
wire. See Figure 1.
12. Close and lock the CPU section.
13. Plug in and turn on the game.
14. When the game is finished booting, calibrate the touchscreen.
FIGURE 1 - CLOSEUP OF CPU SECTION
FIGURE 2 - CLOSEUP OF MONITOR HINGE
Troubleshooting Information - Removal/Installation of Major Assemblies -
eVo/eVo Wallette/Elite Edge Ion
Megatouch Ion Technical Reference Manual
DONGLE SOCKET
ASSEMBLY
TOUCHSCREEN
CONTROLLER
CABLE ON
TOUCHSCREEN
CONTROLLER
OSD
BOARD
LCD MOUNTING
BRACKET
VGA MONITOR CABLE
OSD
CABLE
VGA MONITOR CABLE
GROUND WIRE
TOUCHSCREEN
CONTROLLER
CABLE GROUND
WIRE
TOUCHSCREEN
POWER CABLE
CPU SIDE OF HINGE
MONITOR
SIDE OF
HINGE
LCD POWER CONNECTOR