Megatouch Force Hard Drive Upgrade (PM0513-16)

Visit the AMI Entertainment Network Web site

http://www.amientertainment.com

PM0513-16

Megatouch Force

Hard Drive Upgrade

Table of Contents

Force, Megatouch, MegaNet and TournaMAXX are registered trademarks of AMI.

Reproduction of this manual, in any form or by any means, is strictly forbidden without the written permission of AMI.

Hard Drive Removal and
Installation .................................................................................. p. 1-13

Classic ...................................................................................... p. 2

Elite ........................................................................................... p. 3

Radion ....................................................................................... p. 4

eVo, eVo Wallette, and Elite Edge ............................................. p. 5

VIBE .......................................................................................... p. 6

Fusion ....................................................................................... p. 7

Upright without Coin Door .......................................................... p. 8

Upright with Coin Door ............................................................... p. 9-10

Combo Jukebox ......................................................................... p. 11-12

Maxx-to-Force Converted Games .............................................. p. 13

Security Key Installation ........................................................... p. 14

Software License
Agreements................................................................................. p. 15-20

English ...................................................................................... p. 15-16

French ....................................................................................... p. 17-18

German ...................................................................................... p. 19-20

Megatouch Force Hard Drive Upgrade

1 MEGATOUCH FORCE HARD DRIVE UPGRADE PM0513-16

FIGURE 1 - NEW HARD DRIVE ASSEMBLY

SCREWS AND
WASHERS
SECURING
NEW HARD
DRIVE
ASSEMBLY
TO THE EXISTING
MOUNTING
PLATE
(BOTH SIDES)

EXISTING HARD DRIVE
MOUNTING BRACKET

POWER CONNECTOR
(BLACK WIRE ON TOP,
RED WIRE ON BOTTOM)

CONNECT THE HARD
DRIVE RIBBON CABLE IN
THE GAME TO THIS
ADAPTER ON THE NEW
HARD DRIVE ASSEMBLY
(THE RED STRIPE ON
RIBBON CABLE SHOULD
BE ON THIS SIDE)

Follow the installation instructions for your game type.

HARD DRIVE

HARD DRIVE RIBBON CABLE

HARD DRIVE POWER CONNECTOR

(4) SCREWS SECURING
HARD DRIVE
TO MOUNTING PLATE

BASE OF CABINET

SCREW SECURING
HARD DRIVE
MOUNTING PLATE

Force Classic Games

Hard Drive Removal

If you are connected to TournaMAXX
or TournaCHAMP, you must perform an
Update From Server before remov-
ing the hard drive so that no informa-
tion is deleted.

Turn off and unplug the game.

Unlock and open the lid.

Remove the screw securing the hard
drive mounting plate to the game and
remove the hard drive assembly as
much as the cabling will allow. See
Figure 2.

Disconnect the 4-pin power connector
and the ribbon cable from the hard
drive, then remove the hard drive as-
sembly from the game.

Remove the 4 screws and shoulder
washers securing the hard drive to the
mounting plate. See Figure 2.

Hard Drive Installation

Fasten the new hard drive assembly
to the existing mounting plate with the
4 screws and shoulder washers. See
Figure 1.

FIGURE 2 - FORCE CLASSIC CHASSIS

PM0513-16 MEGATOUCH FORCE HARD DRIVE UPGRADE 2

Connect the 4-pin power connector in
the game to the mating 4-pin connector
attached to the hard drive adapter. See
Figure 1.

Carefully reconnect the ribbon cable in
the game to the new hard drive as
shown in Figure 1. The red stripe on
the cable should be on the opposite
side as the power connector. You may
need to create extra slack in the cable
in order to connect it.

10. Fasten the hard drive mounting plate to

the game with the mounting screw. See
Figure 2.

11. Continue with Security Key Installa-

tion if you are installing a security key.

12. Close and lock the lid.

13. Plug in and turn on the game. The game

will reboot twice to configure the hard-
ware. When prompted, perform a
touchscreen calibration.

14. If you are connected to TournaMAXX

or TournaCHAMP, you must re-enter the
dial-in settings, make the initial call into
the server and then perform two Up-
dates From Server. Refer to the
MegaNet manual for information.

SCREW
SECURING
HARD DRIVE
MOUNTING
PLATE

FIGURE 3 - ELITE WITH REAR DOOR OPEN

3 MEGATOUCH FORCE HARD DRIVE UPGRADE PM0513-16

Force Elite Games

Hard Drive Removal

If you are connected to TournaMAXX
or TournaCHAMP, you must perform an
Update From Server before remov-
ing the hard drive so that no informa-
tion is deleted.

Turn off and unplug the game.

Unlock and open the rear door.

Remove the screw securing the hard
drive mounting plate (see Figure 3) and
slide the hard drive assembly towards
the back of the unit.

Lift the hard drive assembly out of the
game until you’re able to disconnect the
4-pin power connector and the hard
drive ribbon cable from the rear of the
hard drive.

Remove the 4 screws and shoulder
washers fastening the hard drive to
the mounting plate.

Hard Drive Installation

Fasten the new hard drive assembly
to the existing mounting plate with the
4 screws and shoulder washers. See
Figure 1.

Connect the 4-pin power connector in
the game to the mating 4-pin connector
attached to the hard drive adapter. See
Figure 1.

10. Slide the hard drive assembly into the

game and fasten it with the mounting
screw.

11. Continue with Security Key Installa-

tion if you are installing a security key.

12. Close and lock the rear door.

13. Restore power to the game. The game

will reboot twice to configure the hard-
ware. When prompted, perform a
touchscreen calibration.

14. If you are connected to TournaMAXX

or TournaCHAMP, you must re-enter the
dial-in settings, make the initial call into
the server and then perform two Up-
dates From Server. Refer to the
MegaNet manual for information.

PM0513-16 MEGATOUCH FORCE HARD DRIVE UPGRADE 4

SCREWS

SECURING

HARD DRIVE

MOUNTING

BRACKET

FIGURE 4 - SIDE VIEW OF RADION GAME

Force Radion

Hard Drive Removal

If you are connected to TournaMAXX
or TournaCHAMP, you must perform an
Update From Server before remov-
ing the hard drive so that no informa-
tion is deleted.

Turn off and unplug the game.

Unlock and open/remove the rear door
and the left side door.

Locate the hard drive and remove the
2 screws securing the hard drive
mounting bracket to the game (see Fig-
ure 4), then remove the hard drive as-
sembly until you’re able to disconnect
the hard drive power connector and
the motherboard ribbon cable.

Remove the 4 screws and shoulder
washers fastening the hard drive to
the mounting plate.

Hard Drive Installation

Fasten the new hard drive assembly
to the existing mounting plate with the
4 screws and shoulder washers. See
Figure 1.

Connect the 4-pin power connector in
the game to the mating 4-pin connector
attached to the hard drive adapter. See
Figure 1.

Replace the hard drive assembly in the
game and fasten it with the 2 screws.
See Figure 4.

10. Continue with Security Key Installa-

tion if you are installing a security key.

11. Close/replace and lock the rear door

and the side door.

12. Restore power to the game. The game

will reboot twice to configure the hard-
ware. When prompted, perform a
touchscreen calibration.

13. If you are connected to TournaMAXX

or TournaCHAMP, you must re-enter the
dial-in settings, make the initial call into
the server and then perform two Up-
dates From Server. Refer to the
MegaNet manual for information.

Force eVo, eVo Wallette and Elite
Edge

Hard Drive Removal

If you are connected to TournaMAXX
or TournaCHAMP, you must perform an
Update From Server before remov-
ing the hard drive so that no informa-
tion is deleted.

Turn off and unplug the game.

Unlock and open the CPU section.

Remove the 3 screws securing the hard
drive mounting bracket to the game (the
top screw also secures the strain re-
lief cord, so you must support the front
of the game during removal). Then re-
move the hard drive assembly until
you’re able to disconnect the hard drive
power connector and the hard drive
ribbon cable running to the
motherboard. See Figure 5.

Remove the 4 screws and shoulder
washers fastening the hard drive to
the mounting plate. See Figure 5.

Hard Drive Installation

Fasten the new hard drive assembly
to the existing mounting plate with the

SCREWS AND
SHOULDER
WASHERS
FASTENING
HARD DRIVE TO
MOUNTING
PLATE
(BOTH SIDES)

RIBBON
CABLE

SCREWS

FASTENING

HARD

DRIVE

MOUNTING

PLATE TO

GAME

POWER

CONNECTOR

FIGURE 5 - HARD DRIVE - SCREWS FASTENING HARD DRIVE MOUNTING PLATE

5 MEGATOUCH FORCE HARD DRIVE UPGRADE PM0513-16

4 screws and shoulder washers. See
Figure 1.

Connect the 4-pin power connector in
the game to the mating 4-pin connector
attached to the hard drive adapter. See
Figure 1.

Fasten the hard drive mounting plate to
the game with the three screws. See
Figure 5.

10. Continue with Security Key Installa-

tion if you are installing a security key.

11. Close and lock the CPU section.

12. Plug in and turn on the game. The game

will reboot twice to configure the hard-
ware. When prompted, perform a
touchscreen calibration.

13. If you are connected to TournaMAXX

or TournaCHAMP, you must re-enter the
dial-in settings, make the initial call into
the server and then perform two Up-
dates From Server. Refer to the
MegaNet manual for information.

HARD DRIVE

RIBBON CABLE

HARD DRIVE

POWER CONNECTOR

SCREWS SECURING

HARD DRIVE TO

MOUNTING PLATE

(4 PLACES)

SCREWS SECURING

HARD DRIVE

TO PROCESSOR

FIGURE 6 - TOP VIEW OF PROCESSOR WITH COVER REMOVED

VIBE Games

Hard Drive Removal

If you are connected to TournaMAXX
or TournaCHAMP, you must perform an
Update From Server before remov-
ing the hard drive so that no informa-
tion is deleted.

Turn off and unplug the game.

Unlock the lock on the processor cover
and loosen the 3 screws on either side
of the cover. Slide the cover away
from the connector side of the proces-
sor and lift the cover off of the unit.

Remove the 3 screws securing the hard
drive to the processor (see Figure 6).

Disconnect the I/O and audio harness,
then remove the hard drive assembly
until you’re able to disconnect the hard
drive ribbon cable and hard drive power
connector. See Figure 6.

Remove the 4 screws and shoulder
washers fastening the hard drive to
the mounting plate. See Figure 6.

Hard Drive Installation

Fasten the new hard drive assembly
to the existing mounting plate with the
4 screws and washers. See Figure 1.

Connect the 4-pin power connector in
the game to the mating 4-pin connector
attached to the hard drive adapter. See
Figure 1.

10. Fasten the hard drive assembly to the

processor with the 3 screws (see Fig-
ure 6).

11. Continue with Security Key Installa-

tion if you are installing a security key.

12. Replace the processor cover and se-

cure it with the 6 screws.

13. Plug in and turn on the game. The game

will reboot twice to configure the hard-
ware. When prompted, perform a
touchscreen calibration.

14. If you are connected to TournaMAXX

or TournaCHAMP, you must re-enter the
dial-in settings, make the initial call into
the server and then perform two Up-
dates From Server. Refer to the
MegaNet manual for information.

PM0513-16 MEGATOUCH FORCE HARD DRIVE UPGRADE 6

FIGURE 7 - FUSION HARD DRIVE

Force Fusion Games
Hard Drive Removal

If you are connected to TournaMAXX
or TournaCHAMP, you must perform an
Update From Server before remov-
ing the hard drive so that no informa-
tion is deleted.

Turn off and unplug the game.

Unlock and open the bezel.
Games with electronic boxes: Remove
the 2 screws fastening the electronics
box cover and remove the cover.

Locate the hard drive. It will either be
mounted to the electronics box cover
or against the back wall of the game.
Remove the 3 screws or standoffs
securing the hard drive mounting
bracket to the cover or the game, then
remove the hard drive assembly until
you’re able to disconnect the hard drive
power connector and hard drive rib-
bon cable.

Remove the 4 screws and shoulder
washers fastening the hard drive to
the mounting plate (see Figure 7).

Hard Drive Installation

Fasten the new hard drive assembly
to the existing mounting plate with the
4 screws and shoulder washers. See
Figure 1.

Connect the 4-pin power connector in
the game to the mating 4-pin connector
attached to the hard drive adapter. See
Figure 1.

Fasten the hard drive assembly to the
electronics box cover or game with the
3 screws or standoffs. See Figure 7.

10. Continue with Security Key Installa-

tion if you are installing a security key.

11. Close and lock the bezel.

Games with electronic boxes: Replace
the electronics box cover and fasten it
with the 2 screws.

12. Plug in and turn on the game. The game

will reboot twice to configure the hard-
ware. When prompted, perform a
touchscreen calibration.

13. If you are connected to TournaMAXX

or TournaCHAMP, you must re-enter the
dial-in settings, make the initial call into
the server and then perform two Up-
dates From Server. Refer to the
MegaNet manual for information.

POWER
CONNECTOR

RIBBON

CABLE

HARDWARE

FASTENING

HARD DRIVE

MOUNTING

PLATE TO

GAME

(3 PLACES)

SCREWS AND

SHOULDER

WASHERS

FASTENING

HARD DRIVE TO

MOUNTING

PLATE

(4 PLACES)

7 MEGATOUCH FORCE HARD DRIVE UPGRADE PM0513-16

FIGURE 8 - HARD DRIVE MOUNTING PLATE ATTACHED TO CPU SHELF

SCREW SECURING

HARD DRIVE

MOUNTING PLATE

TO THE GAME

SCREW SECURING

HARD DRIVE TO

MOUNTING PLATE

(4 PLACES)

Force Upright without Coin Door
Hard Drive Removal

If you are connected to TournaMAXX
or TournaCHAMP, you must perform an
Update From Server before remov-
ing the hard drive so that no informa-
tion is deleted.

Turn off and unplug the game.

Unlock and open the front bezel.

Slide the CPU shelf into its service po-
sition to access the hard drive.

Remove the screw securing the hard
drive mounting plate to the shelf (see
Figure 8).

Remove the 4 screws and shoulder
washers fastening the hard drive to
the mounting plate. See Figure 8.

Disconnect the hard drive ribbon cable
and the hard drive power connector
from the hard drive.

Hard Drive Installation

Fasten the new hard drive assembly
to the existing mounting plate with the
4 screws and shoulder washers. See
Figure 1.

Connect the 4-pin power connector in
the game to the mating 4-pin connector
attached to the hard drive adapter. See
Figure 1.

10. Carefully reconnect the ribbon cable in

the game to the new hard drive as
shown in Figure 1. The red stripe on
the cable should be on the opposite
side as the power connector. You may
need to create extra slack in the cable
in order to connect it.

11. Fasten the hard drive assembly to the

CPU shelf with the mounting screw
(see Figure 8).

12. Continue with Security Key Installa-

tion if you are installing a security key.

13. Slide the CPU shelf back into the game.

14. Close and lock the front bezel.

15. Plug in and turn on the game. The game

will reboot twice to configure the hard-
ware. When prompted, perform a
touchscreen calibration.

16. If you are connected to TournaMAXX

or TournaCHAMP, you must re-enter the
dial-in settings, make the initial call into
the server and then perform two Up-
dates From Server. Refer to the
MegaNet manual for information.

PM0513-16 MEGATOUCH FORCE HARD DRIVE UPGRADE 8

Force Upright with Coin Door

Hard Drive Removal

If you are connected to TournaMAXX
or TournaCHAMP, you must perform an
Update From Server before remov-
ing the hard drive so that no informa-
tion is deleted.

Turn off and unplug the game.

Unlock and open the front door to ac-
cess the electronics shelf.

The I/O board assembly will need to be
moved aside in order to access the hard
drive. Remove the 2 screws securing
the I/O board mounting plate to the hard
drive mounting plate (see Figure 9).

Remove the screw securing the hard
drive mounting plate to the game (see
Figure 10).

Disconnect the hard drive ribbon cable
and the hard drive power connector
from the hard drive.

Remove the 4 screws and shoulder
washers fastening the hard drive to
the mounting plate (see Figure 9) and
remove the hard drive.

Hard Drive Installation

Fasten the new hard drive assembly
to the existing mounting plate with the
4 screws and shoulder washers. See
Figure 1.

Connect the 4-pin power connector in
the game to the mating 4-pin connector
attached to the hard drive adapter. See
Figure 1.

10. Carefully reconnect the ribbon cable in

11. Fasten the hard drive mounting plate to

the game with the mounting screw (see
Figure 10).

12. Fasten the I/O board mounting plate to

the hard drive mounting plate with the
2 screws (see Figure 9).

13. Continue with Security Key Installa-

tion if you are installing a security key.

14. Close and lock the front door.

15. Plug in and turn on the game. The game

will reboot twice to configure the hard-
ware. When prompted, perform a
touchscreen calibration.

16. If you are connected to TournaMAXX

or TournaCHAMP, you must re-enter the
dial-in settings, make the initial call into
the server and then perform two Up-
dates From Server. Refer to the
MegaNet manual for information.

9 MEGATOUCH FORCE HARD DRIVE UPGRADE PM0513-16

SCREWS
SECURING
I/O BOARD
MOUNTING

PLATE TO
HARD
DRIVE
MOUNTING
PLATE

SCREWS

SECURING

HARD DRIVE

TO MOUNTING

PLATE

(BOTH SIDES)

FIGURE 9 - SIDE VIEW OF HARD DRIVE

SCREW

SECURING

HARD DRIVE

MOUNTING

PLATE

FIGURE 10 - TOP VIEW OF I/O BOARD AND HARD DRIVE

PM0513-16 MEGATOUCH FORCE HARD DRIVE UPGRADE 10

Megatouch Combo Jukebox

Hard Drive Removal

If you are connected to TournaMAXX
or TournaCHAMP, you must perform an
Update From Server before remov-
ing the hard drive so that no informa-
tion is deleted.

Turn off the main power switch on the
outside of the game.

Unlock and remove the rear door, then
turn off the internal power switch (lo-
cated above the cooling fan on the left
side). Then unplug the game.

Remove the screw securing the hard
drive mounting plate to the electronics
tray (see Figure 11).

The I/O board assembly will need to be
moved aside in order to access the hard
drive. Remove the 2 screws securing
the I/O board mounting plate to the hard
drive mounting plate. See Figure 11.

Disconnect the power connector and
the ribbon cable from the hard drive
(see Figure 11).

Remove the 4 screws and shoulder
washers fastening the hard drive to
the hard drive mounting plate. See Fig-
ure 11.

Hard Drive Installation

Fasten the new hard drive assembly
to the existing mounting plate with the
4 screws and shoulder washers. See
Figure 1.

Connect the 4-pin power connector in
the game to the mating 4-pin connector
attached to the hard drive adapter. See
Figure 1.

10. Carefully reconnect the ribbon cable in

11. Resecure the I/O board mounting plate

to the hard drive assembly with the 2
screws (see Figure 11).

12. Fasten the hard drive and I/O board

assemblies to the electronics tray with
the mounting screw (see Figure 11).

13. Continue with Security Key Installa-

tion if you are installing a security key.

14. Plug in the game, then turn on the inter-

nal power switch and replace and lock
the rear door.

15. Turn on the main power switch on the

outside of the game. The game will
reboot twice to configure the hard-
ware. When prompted, perform a
touchscreen calibration.

16. If you are connected to TournaMAXX

or TournaCHAMP, you must re-enter the
dial-in settings, make the initial call into
the server and then perform two Up-
dates From Server. Refer to the
MegaNet manual for information.

11 MEGATOUCH FORCE HARD DRIVE UPGRADE PM0513-16

FIGURE 11 - COMBO JUKEBOX ELECTRONICS SHELF

SCREW

SECURING

HARD DRIVE

SCREWS

SECURING

I/O BOARD

MOUNTING PLATE

TO HARD DRIVE

ASSEMBLY

SCREWS SECURING HARD DRIVE
TO HARD DRIVE MOUNTING PLATE
(4 PLACES)

HARD DRIVE

RIBBON CABLE

HARD DRIVE

POWER

CONNECTOR

PM0513-16 MEGATOUCH FORCE HARD DRIVE UPGRADE 12

13 MEGATOUCH FORCE HARD DRIVE UPGRADE PM0513-16

FIGURE 12 - HARD DRIVE IN MAXX TO FORCE CONVERTED GAMES

Maxx-to-Force Converted Games
Hard Drive Removal

If you are connected to TournaMAXX
or TournaCHAMP, you must perform an
Update From Server before remov-
ing the hard drive so that no informa-
tion is deleted.

Turn off and unplug the game.

Unlock and open the CPU section door.

Remove the 3 screws or standoffs
securing the hard drive mounting
bracket to the electronics tray, then re-
move the hard drive assembly until
you’re able to disconnect the hard drive
power connector and hard drive rib-
bon cable.

Remove the 4 screws and shoulder
washers fastening the hard drive to
the mounting plate (see Figure 12).

Hard Drive Installation

Fasten the new hard drive assembly
to the existing mounting plate with the
4 screws and shoulder washers. See
Figure 1.

Connect the 4-pin power connector in
the game to the mating 4-pin connector
attached to the hard drive adapter. See
Figure 1.

Fasten the hard drive assembly to the
electronics tray with the 3 screws or
standoffs. See Figure 12.

10. Continue with Security Key Installa-

tion if you are installing a security key.

11. Close and lock the CPU section.

12. Plug in and turn on the game. The game

will reboot twice to configure the hard-
ware. When prompted, perform a
touchscreen calibration.

13. If you are connected to TournaMAXX

or TournaCHAMP, you must re-enter the
dial-in settings, make the initial call into
the server and then perform two Up-
dates From Server. Refer to the
MegaNet manual for information.

POWER
CONNECTOR

RIBBON

CABLE

HARDWARE

FASTENING

HARD DRIVE

MOUNTING

PLATE TO

GAME

(3 PLACES)

SCREWS AND

SHOULDER

WASHERS

FASTENING

HARD DRIVE TO

MOUNTING

PLATE

(4 PLACES)

Security Key Installation
(for kits with security keys)

Locate the security key (the button-
shaped disc with the handle) on the
I/O board or control board.

Remove the existing security key from
the board and replace it with the sup-
plied security key.

Close and lock the CPU section door of
the game and restore power to the
game. The game will reboot twice to
configure the hardware. When
prompted, perform a touchscreen cali-
bration.

If you are connected to TournaMAXX
or TournaCHAMP, you must re-enter the
dial-in settings, make the initial call into
the server and then perform two Up-
dates From Server. Refer to the
MegaNet manual for information.

PM0513-16 MEGATOUCH FORCE HARD DRIVE UPGRADE 14

15 MEGATOUCH FORCE HARD DRIVE UPGRADE PM0513-16

AMI Entertainment Network, Inc. Software License Agreement

AMI Entertainment Network, Inc. (“Licensor”) is willing to license the enclosed software to
you only if you accept all of the terms in this license agreement (“Agreement”).

Ownership of the Software
1.

The enclosed Megatouch® product, which may include but is not limited to the
Megatouch software program (“Software”) and the accompanying written materials,
are owned by Licensor and are protected by United States copyright laws, patent
laws and other intellectual property laws, by laws of other nations, and by international
treaties.

Restrictions on Use and Transfer
2.

If this Software package contains multiple media types (such as CDs, flash cards,
hard drives, etc), then you may use only the type of media appropriate for your
Machine. You may not use the other media types on another Machine, or transfer, or
assign them to another user except as part of the permanent transfer of the Software
and all written materials (as provided for below in paragraph 4).

You may make one copy of the software for backup purposes only. You may not
copy or make backup copies of any software security key or software security
device under any circumstances.

You may permanently transfer the right to use the Software and accompanying
written materials (including the most recent update and all prior versions) if you retain
no copies and the transferee agrees in writing to be bound by the terms of this
Agreement. Such a transfer of this license to another party immediately terminates
your license. You may not otherwise transfer or assign the right to use the Software,
except as stated in this paragraph.

You may not operate or allow the operation of the Software at locations where the
operation of such Software does not comply with all local, state, and other
governmental body laws and regulations. You agree to not use or permit the use of
the Software in violation of any U.S. Federal, state, or local laws or regulations or
any foreign law or regulation, including laws regarding gaming, gambling or intellectual
property rights in or concerning the Software.

You may not modify, adapt, translate, reverse engineer, decompile, disassemble the
Software or create derivative works from the Software or any component thereof;
nor may you remove, modify or hide or otherwise make unreadable or non-viewable
any notice, legend, advice, watermark or other designation contained on the Software,
component thereof, or output therefrom.

You agree that the Software and the authorship, systems, ideas, inventions methods
of operation, documentation and other information contained therein, and all versions,
modifications and adaptations thereto are proprietary intellectual properties of Licensor
and are protected by civil and criminal law, and by copyright, trade secret, trademark
and the patent laws of the United States and other countries.

Limited Warranty
8.

Licensor warrants, solely for your benefit, that the Software will function in material
conformity, with its accompanying documentation for a period outlined in Licensor’s
standard product warranty period after your receipt of the Software.

Licensor’s Obligations Under Warranty
9.

Licensor’s sole obligation under the aforesaid warranty shall be to utilize commercially
reasonable efforts to correct or modify such portion of the Software as to make it
materially conform with the applicable documentation.

PM0513-16 MEGATOUCH FORCE HARD DRIVE UPGRADE 16

Grant Of License
10. Licensor grants to you a limited, non-exclusive license to distribute and/or use one

copy of the Software on a single Megatouch (“Machine”) accompanied by a single
licensor factory authorized security key. Licensor reserves the right to update
versions of the software and the content to the Machine as deemed appropriate by
the Licensor. You are entrusted to maintain and protect your single licensor factory
authorized security key, password, or other identification from being utilized by any
third party, and you agree to be responsible for any use of the Software provided
herein by a third party utilizing your identification. Licensor maintains the right to
immediately terminate your License for reasons related to misuse or other non-
conformity with the rules expressed herein. While Licensor does not routinely inspect
Machines, Licensor also reserves the right to inspect or audit the Software from time
to time in Licensor’s sole discretion. To the extent that Licensor’s access to the
Software requires that Licensor also gain access to a Machine in which the Software
is installed, you agree to promptly provide Licensor, when requested, with permission
and aid in Licensor gaining access to the Machine.

Disclaimers
11. EXCEPT AS PROVIDED IN THE SECTION ENTITLED “LIMITED WARRANTY”, LICENSOR

MAKES NO OTHER PROMISES, REPRESENTATIONS OR WARRANTIES, WHETHER
EXPRESSED OR IMPLIED, REGARDING OR RELATING TO THE SOFTWARE OR
CONTENT THEREIN OR TO ANY OTHER MATERIAL FURNISHED OR PROVIDED TO
YOU PURSUANT TO THIS AGREEMENT OR OTHERWISE AND LICENSOR SPECIFICALLY
DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE WITH RESPECT TO SAID MATERIALS OR THE USE THEREOF.
TO THE MAXIMUM EXTENT ALLOWABLE BY LAW THE UNIFORM COMMERCIAL CODE
OR OTHER UNIFORM LAWS SHALL NOT APPLY TO THIS AGREEMENT.

Limitation on Liability
12. IN NO EVENT SHALL LICENSOR BE LIABLE UNDER ANY CLAIM, DEMAND OR ACTION

ARISING OUT OF OR RELATING TO THE SOFTWARE, ITS USE, INSTALLATION OR
LICENSOR’S PERFORMANCE OR LACK THEREOF UNDER THIS AGREEMENT FOR
ANY SPECIAL, INDIRECT, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES,
WHETHER OR NOT LICENSOR HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
CLAIM, DEMAND OR ACTION. IN ADDITION, WITHOUT LIMITING THE FOREGOING, IN
ALL EVENTS THE REMEDIES AVAILABLE TO YOU SHALL BE LIMITED TO THE AMOUNT
PAID BY YOU TO LICENSOR FOR THE SOFTWARE.

13. IN NO EVENT WILL LICENSOR BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY

LOSS OF PROFITS, LOST SAVINGS, OR OTHER INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF YOUR USE, MISUSE, BREACH OF THIS AGREEMENT OR
INABILITY TO USE THE SOFTWARE.

General
14. The validity and construction of this Agreement and of the rights and obligations herein

shall be determined and governed by the laws of the State of New York. By accepting
the terms of this Agreement, you acknowledge and accept that the courts of New
York, New York shall have exclusive jurisdiction and venue regarding any disputes
arising with regard to this Agreement or arising out of activity or misuse of the
Software.

15. AMI Entertainment Network, Inc. in its sole discretion, may assign this agreement or

any of its rights and obligations hereunder.

16. If you have any questions concerning this Agreement or wish to contact Licensor for

any reason, please write: AMI Entertainment Network, Inc., 155 Rittenhouse Circle,
Bristol, PA 19007, USA.

17 MEGATOUCH FORCE HARD DRIVE UPGRADE PM0513-16

Contrat de licence de logiciel de AMI Entertainment Network, Inc.

AMI Entertainment Network, Inc. (ci-après le "Concédant") est disposé à vous accorder la licence
d'utilisation du logiciel ci-inclus, à condition que vous vous engagiez à respecter tous les termes,
clauses et conditions du présent contrat de licence (Contrat).

Droit de Propriété
1.

Le produit Megatouch® ci-joint contenant, mais ne s'y limitant pas, le logiciel Megatouch (ci-
après le "logiciel") et toute la documentation écrite, restent la propriété du Concédant et sont
protégés par : les lois de droits d'auteur des Etats-Unis, les lois s'appliquant aux brevets
déposés et à la propriété intellectuelle, ainsi que par celles des autres pays et les traités
internationaux.

Restriction d'Utilisation et Transfert
2.

Si le présent logiciel comprend plusieurs types de composants (tels que CD-ROM, cartes
flash, disques durs, etc), vous ne pouvez utilisez que ceux qui conviennent à votre appareil.
Il est strictement interdit de les utiliser sur un autre appareil, les transférer -ou les céder à un
autre utilisateur, sauf en cas de transfert permanent du logiciel et de toute la documentation
écrite (comme indiqué ci-dessous au paragraphe 4).

Il est interdit de copier le logiciel, à l'exception d'une copie de sauvegarde. Il est aussi interdit
de reproduire -ou faire des copies de sauvegarde des programmes de clé de sécurité ou
autres fichiers de sécurité, quelles que soient les circonstances.

Vous pouvez céder en permanence à un tiers -le droit d'utiliser le LOGICIEL et toute la
documentation écrite l'accompagnant, (ainsi que la plus récente mise à jour et toutes autres
anciennes versions) seulement si vous n'en gardez aucune copie, et si le cessionnaire
s'engage, par écrit, à respecter les termes, clauses et conditions du présent Contrat. Cette
cession à un tiers met fin à votre licence immédiatement. Autrement, vous n'avez pas la
permission de transférer ou d'accorder à un tiers le droit d'utiliser le présent logiciel, excepté
que tel que décrit dans le présent paragraphe.

Il est interdit d'utiliser le présent logiciel ou de permettre son utilisation dans des emplacements
où l'utilisation du présent logiciel n'est pas conforme aux lois et réglementations locales,
nationales ou réglementations d'autres organismes gouvernementaux. Vous acceptez de ne
pas utiliser ou d'autoriser l'utilisation du logiciel d'une manière enfreignant les lois ou regula-
tions s'appliquant à la propriété intellectuelle et au jeu, en vigueur aux Etats-Unis ou dans les
autres pays du monde, y compris les lois de l'ensemble du logiciel.

Il est interdit de modifier, adapter, traduire, démonter, décompiler, désassembler le logiciel ou
créer du matériel dérivé du logiciel ou de tout composant de celui-ci ; vous ne pouvez pas
enlever, modifier ou cacher ou rendre illisible ou non-visible toute instruction, légende, infor-
mation ou filigrane ou autre désignation qui apparaît dans le logiciel, composant dudit logiciel
ou résultant dudit logiciel.

Vous convenez que le logiciel et les droits d'auteur, les systèmes, les idées, les inventions, les
méthodes d'utilisation, la documentation et autre information incluse, ainsi que toutes les
versions, modifications et adaptations qui s'y rattachent sont les propriétés intellectuelles du
Concédant et sont protégées par le droit civil et pénal et par le droit d'auteur, le secret
commercial, la marque déposée et le brevet aux Etats-Unis et dans les autres pays du monde.

Limite de Garantie
8.

Le Concédant garantit seulement à votre intention, que le logiciel permettra une utilisation
conforme, avec la documentation l'accompagnant, pendant la période de temps indiquée
dans la période de garantie du produit standard du Concédant, à compter de la date de
livraison du logiciel.

Responsabilité du Concédant aux termes de la Garantie
9.

La seule obligation du Concédant aux termes de la garantie susmentionnée sera de faire tous
les efforts commercialement raisonnables pour corriger ou modifier la partie du logiciel pour
le rendre matériellement conforme aux spécifications de la documentation.

PM0513-16 MEGATOUCH FORCE HARD DRIVE UPGRADE 18

Concession de Licence
10. Le Concédant vous accorde le droit d'utiliser une seule copie par appareil Megatouch (ci-

après "Appareil") accompagné d'une seule clé de sécurité autorisée en usine et fournie par
le Concédant. Le Concédant se réserve le droit de mise à jour des versions du logiciel et du
contenu de l'Appareil, quand il juge nécessaire de le faire. Il vous appartient également
d'empêcher que les mots de passe ou autres codes et la clé de sécurité soient utilisés par un
tiers. Vous acceptez d'assumer la responsabilité dans le cas de l'utilisation du logiciel par un
tiers. Le Concédant se réserve le droit de résilier votre contrat de licence à tout moment dans
l'éventualité d'une utilisation non-conforme aux clauses stipulées. Bien que le Concédant ne
contrôle pas les appareils périodiquement, il se réserve toutefois le droit de contrôler le logiciel
à tout moment et sans préavis de sa part. De surcroît, dans l'éventualité où le logiciel n'est
accessible qu'à travers la machine dans laquelle il est installé, le licencié s'engage à donner
libre accès au Concédant, ou ses représentants, à la machine et dans les plus brefs délais.

Exclusion de toute autre garantie
11. EXCEPTE COMME PREVU DANS LA SECTION INTITULEE "LIMITE DE GARANTIE", LE CONCEDANT

N'ASSURE AUCUNE AUTRE GARANTIE DE QUELQUE NATURE ET A QUELQUE TITRE QUE CE
SOIT, EXPLICITE OU IMPLICITE, EN RAPPORT AVEC LE LOGICIEL ET LES COMPOSANTS QUI
L'ACCOMPAGNENT OU, LE CAS ECHEANT, TOUT SUPPORT OU MATERIEL FOURNI
CONFORMEMENT AU PRESENT CONTRATEN PARTICULIER, LE CONCEDANT NE PEUT
DONNER AUCUNE GARANTIE, DE QUELQUE NATURE QUE CE SOIT, POUR LA
COMMERCIALISATION DE TOUS LES PRODUITS EN RAPPORT AVEC LE LOGICIEL OU AVEC
L'UTILISATION DE CELUI-CI. DANS LA MESURE OU CELA EST PERMIS PAR LA LOI, LE CODE
UNIFORME COMMERCIAL OU AUTRE LOI UNIFORME NE S'APPLIQUE PAS AU PRESENT
CONTRAT.

Limite de Responsabilité
12. LE CONCEDANT NE SERA EN AUCUN CAS RESPONSABLE DE TOUTE RECLAMATION,

DEMANDE OU ACTION RESULTANT DE OU EN RAPPORT AVEC LE LOGICIEL, SON UTILISATION
OU SON INSTALLATION, OU LA PERFORMANCE OU MANQUE DE PERFORMANCE DU
CONCEDANT EN VERTU DU PRESENT CONTRAT POUR TOUS DOMMAGES D'UNE NATURE
QUI N'EST PAS PRESUMEE PAR LA LOI ET QUI DOIVENT ETRE EXPRESSEMENT PROUVES,
DOMMAGE INDIRECTS, DOMMAGES-INTERETS POUR PREJUDICE MORAL, QUE LE
CONCEDANT AIT ETE AVISE OU NON DE LA POSSIBILITE D'UNE TELLE RECLAMATION,
DEMANDE OU ACTION. DE PLUS, SANS LIMITER CE QUI PRECEDE, LES DEDOMMAGEMENTS
A VOTRE DISPOSITION SERONT LIMITES AU MONTANT QUE VOUS AUREZ PAYE AU
CONCEDANT POUR LE LOGICIEL.

13. LE CONCEDANT NE SERA EN AUCUN CAS RESPONSIBLE : D'UNE RUPTURE DE CONTRAT,

DES DOMMAGES, Y COMPRIS TOUTE PERTE DE PROFIT, PERTES D'ECONOMIE OU TOUS
AUTRES DOMMAGES INDIRECTS OU DOMMAGES-INTERETS ACCESSOIRES DECOULANT
DE LA MAUVAISE UTILISATION OU DE L'IMPOSSIBILITE D'UTILISATION DU LOGICIEL.

Dispositions Générales
14. La validité et la construction du présent Contrat et les droits et obligations ci-inclus seront

déterminés et régis par les lois de l'état de New York aux États-Unis. En acceptant les
dispositions du présent contrat, vous acceptez également que tous litiges ou revendications
relatives seront réglés par voie d'arbitrage par un tribunal de l'état de New York, aux Etats-
Unis.

15. AMI Entertainment Network, Inc. se réserve le droit de transférer le présent Contrat à un

tiers ainsi que ses droits et obligations ci-après.

16. Pour toutes questions concernant le présent Contrat -ou si vous désirez contacter le Concédant

pour une raison quelconque, veuillez écrire à : AMI Entertainment Network, Inc., 155
Rittenhouse Circle, Bristol, PA 19007, Etats-Unis.

19 MEGATOUCH FORCE HARD DRIVE UPGRADE PM0513-16

AMI Entertainment Network, Inc. Softwarelizenzabkommen

AMI Entertainment Network, Inc. („Lizenzgeber”) ist nur dann bereit Ihnen eine Lizenz für die
beiliegende Software zu erteilen, wenn Sie alle Bestimmungen dieses Lizenzabkommens
(“Abkommen”) akzeptieren.
Eigentumsvorbehalt der Software
1.

Das beiliegende Megatouch®-Produkt, welches das Megatouch Softwareprogramm
(„Software”) beinhalten kann, aber nicht darauf beschränkt ist, und die schriftlichen
Unterlagen sind Eigentum des Lizenzgebers und sind durch die Gesetze der Vereinigten
Staaten und anderer Länder und durch internationale Verträge urheberrechtlich
geschützt.

Beschränkungen im Gebrauch und Transfer
2.

Sollte diese Softwarelieferung mehrere Medien enthalten (z.B. CD, Karten, Festplatten
usw.), dürfen Sie nur die für Ihre Maschine angebrachte Medienart verwenden. Die anderen
Medienarten dürfen nicht auf anderen Maschinen verwendet werden oder an Dritte
übergeben werden, abgesehen von einem endgültigen Transfer der Software und aller
schriftlichen Unterlagen (wie im untenstehenden Paragraphen 4 beschrieben).

Sie dürfen nur eine Sicherungskopie der Software herstellen. Unter keinen Umständen
dürfen Sie einen Softwaresicherungsschlüssel oder Sicherungsmaßnahmen kopieren oder
davon Sicherungskopien herstellen.

Sie dürfen das Nutzungsrecht für die Software und die schriftlichen Unterlagen (einschließlich
der aktuellen Version und aller vorhergehenden Versionen) an Dritte übertragen, wenn Sie
keine Kopie behalten und wenn der Empfänger die Bestimmungen dieses Abkommens in
schriftlicher Form akzeptiert. Bei einem solchen Transfer der Lizenz an Dritte erlischt Ihre
Lizenz umgehend. Abgesehen von den Bestimmungen dieses Paragraphen sind alle anderen
Transfers oder Übertragungen der Nutzungsrechte für diese Software unerlaubt.

Sie dürfen die Software nicht benutzen oder eine Nutzung gestatten, wenn eine
solche Nutzung der Software irgendwelche Gesetze und Verordnungen der
kommunalen oder staatlichen Behörden verletzen würde. Sie verpflichten sich die
Software nicht so zu nutzen oder nutzen zu lassen, dass sie damit gegen staatliche,
Bundes- oder Lokalgesetze oder Bestimmungen der USA oder gegen ausländische
Gesetze oder Bestimmungen, einschliesslich aller Gesetze bezüglich Glücksspiels,
Spielens oder geistigen Eigentumrechts der Software, verstossen.

Es ist Ihnen nicht gestattet, die Software abzuändern, zu verändern, zu übersetzen,
rückumzuwandeln, zu dekompilieren oder zu zerlegen, oder aus der Software oder eines
Teils davon andere Werke abzuleiten. Sie dürfen auch aus der Software, einem Bestandteil
der Software oder aus den Datenausgaben der Software keine Hinweise, Bemerkungen,
Ratschläge, Wasserzeichen oder andere Markierungen entfernen, verändern, verbergen
oder auf andere Art unlesbar machen.

Sie akzeptieren, dass die Software und die Urheberschaft, die Systeme, die Ideen,
Erfindungen, die Arbeitsweisen, die Dokumentation und alle anderen darin enthaltenen
Informationen und alle Versionen, Veränderungen, und Bearbeitungen davon das geistige
Eigentum des Lizenzgebers sind, und dass sie durch Straf- und Zivilgesetzgebung und
durch die Copyright-, Geschäftsgeheimnis-, Warenzeichen- und die Patentgesetze der
Vereinigten Staaten und anderer Länder geschützt sind.

Beschränkte Garantie
8.

Der Lizenzgeber garantiert zu Ihren Gunsten, dass die Software für die angegebene
normale Garantiezeit des Lizenzgebers nach Ihrer Annahme der Software in erheblicher
Übereinstimmung mit der beiliegenden Dokumentation laufen wird.

Verpflichtung des Lizenzgebers im Rahmen der Garantie
9.

Die ausschließliche Pflicht des Lizenzgebers im Rahmen der vorstehenden Garantie besteht
darin, alle geschäftlich vertretbaren Schritte zu unternehmen, um Teile der Software zu berichtigen
oder abzuändern, bis sie mit der beiliegenden Dokumentation erheblich übereinstimmen.

PM0513-16 MEGATOUCH FORCE HARD DRIVE UPGRADE 20

Übertragung der Lizenz
10. Der Lizenzgeber gewährt Ihnen eine beschränkte, nicht-ausschliessbare Lizenz zur

Vertreibung und/oder Benutzung einer Kopie der Software auf einem einzelnen Megatouch
(„Gerät”) mit einem einzelnen werksmäßig gestatteten Sicherungsschlüssel. Der Lizenzgeber
behält sich das Recht vor, nach eigenem Ermessen die Software und den Inhalt der Maschine
zu verbessern. Sie sind dafür verantwortlich ihren individuellen, vom Lizenzgeber werksmäßig
gestatteten Sicherheitsschlüssel, ihr Passwort oder anderweitigen Identifikationsmechanismus
instandzuhalten und abzusichern gegen die Nutzung durch eine dritte Partei, und sie akzeptieren
die Verantwortung für jegliche Nutzung der besagten Software durch eine dritte Partei mithilfe
ihresIdentifikationsmechanismus . Obwohl der Lizenzgeber nicht regelmässig Maschinen
inspiziert, behält sich der Lizenzgeber das Recht vor, ihre Lizenz umgehend zu kündigen aus
Gründen des Missbrauchs oder bei Nichtbefolgung der Bestimmungen in diesem Vertrag. Der
Lizenzgeber behält sich ebenfalls das Recht vor, die Software von Zeit zu Zeit nach eigenem
Ermessen zu inspizieren oder zu überprüfen. Im Falle, dass der Lizenzgeber Zugang zu dem
Gerät wünscht, in dem besagte Software installiert ist, erklären Sie sich bereit, dass sie dem
Lizenzgeber, wenn nötig, Erlaubnis und Hilfe beim Zugang zum Gerät verschaffen.

Beschränkungen
11. ABGESEHEN VON DEN BESTIMMUNGEN DES PARAGRAPHEN „BESCHRÄNKTE GARANTIE"

GIBT DER LIZENZGEBER KEINE SONSTIGEN VERSPRECHEN, VERPFLICHTUNGEN ODER
GARANTIEN, OB AUSDRÜCKLICH ODER STILLSCHWEIGEND, FÜR DIE SOFTWARE ODER
IHRE BESTANDTEILE ODER FÜR ALLE ANDEREN MATERIALIEN, DIE IHNEN IM RAHMEN DIESES
ABKOMMENS ZUR VERFÜGUNG GESTELLT ODER ÜBERLASSEN WERDEN, UND DER
LIZENZGEBER LEHNT AUSDRÜCKLICH ALLE ANSPRÜCHE AUF MARKTFÄHIGKEIT UND
EIGNUNG DER BESAGTEN MATERIALIEN FÜR DEN GEWÖHNLICHEN GEBRAUCH AB. SOWEIT
GESETZESMÄSSIG ZUGELASSEN, SOLLEN DIE HANDELSRECHTLICHE GESETZGEBUNG
AUS DEM UNIFORM COMMERCIAL CODE ODER ANDERE GESETZE AUF DIESES ABKOMMEN
NICHT ANWENDBAR SEIN.

Haftungsbeschränkung
12. DER LIZENZGEBER HAT KEINERLEI HAFTUNG BEI EINEM ANSPRUCH, EINER FORDERUNG

ODER EINER KLAGE, DIE AUF NUTZUNG DER SOFTWARE, DEREN INSTALLIERUNG, DER
LEISTUNG DES LIZENZGEBERS ODER DESSEN VERSAGEN IM RAHMEN DIESES ABKOMMENS
FÜR JEGLICHE FOLGE-, INDIREKTE, SONDER- ODER NEBENSCHÄDEN BERUHEN, SELBST
WENN DER LIZENZGEBER AUF DIE MÖGLICHKEIT EINES SOLCHEN ANSPRUCHES, EINER
FORDERUNG ODER EINER KLAGE HINGEWIESEN WURDE. WEITERHIN UND OHNE
BESCHRÄNKUNG DES LETZTEN SATZES, DÜRFEN IN ALLEN FÄLLEN DIE IHNEN ZUR
VERFÜGUNG STEHENDEN ABHILFEN DIE VON IHNEN FÜR DIE SOFTWARE AN DEN
LIZENZGEBER GEZAHLTE SUMME NICHT ÜBERSCHREITEN.

13. DER LIZENZGEBER HAT IN KEINEM FALL EINE HAFTUNG IHNEN GEGENÜBER FÜR SCHÄDEN,

EINSCHLIESSLICH ETWAIGER GEWINNVERLUSTE, NICHT REALISIERTER EINSPARUNGEN
ODER ANDERER NEBEN- ODER FOLGESCHÄDEN, DIE AUS IHRER VERWENDUNG,
MISSBRAUCH, VERLETZUNG DIESES ABKOMMENS ODER GEBRAUCHSUNFÄHIGKEIT DER
SOFTWARE ENTSTEHEN.

Allgemein
14. Die Rechtsgültigkeit und Provisionen dieses Abkommens und der darin enthaltenen Rechte und

Pflichten werden durch die Gesetze des Staates von New York bestimmt. Sollten sie diese
Vereinbarungen annehmen, dann akzeptieren Sie, dass der ausschliessliche Erfüllungsort
und Gerichtsstand bei den Gerichten von New York im Staat New York liegen hinsichtlich aller
Streitigkeiten, die diesen Vertrag betreffen, oder die durch Leistung oder Missbrauch der
besagten Software entstehen.

15. AMI Entertainment Network, Inc. kann nach eigenem Ermessen dieses Abkommen oder

jedes der darin enthaltenen Rechte und Pflichten an Dritte abtreten.

16. Bei Rückfragen über dieses Abkommen oder wenn Sie den Lizenzgeber aus einem anderen

Grund kontaktieren wollen, bitte schreiben an: AMI Entertainment Network, Inc., 155
Rittenhouse Circle, Bristol, PA 19007, USA.

__________________________________________________________________

_______________________________________________________________

________________________________________________________________

___________________________________________________________________

_______________________________________________________________

________________________________________________________________

__________________________________________________________________

_________________________________________________________________

______________________________________________________________

________________________________________________________________

___________________________________________________________________

__________________________________________________________________

_________________________________________________________________

_____________________________________________________________________